Patton 4960 (4 E1/T1)

From SIPfoundry sipXecs IP PBX, The Open Source SIP PBX for Linux - Calivia

The following config is for a Patton 4960 Gateway.

The gateway is configured with a single PRI.

 #----------------------------------------------------------------#
 #                                                                #
 # SN4960/4E24V/UI                                                #
 # R4.T 2006-12-11_RFE438 H323 RBS SIP                            #
 # 2007-02-02T01:22:53                                            #
 # Generated configuration file                                   #
 #                                                                #
 #----------------------------------------------------------------#
 
 cli version 3.20
 administrator administrator password xxxxxx encrypted
 clock local offset -08:00
 # Put in your DNS Server
 dns-client server xxx.xxx.xxx.xxx
 dns-relay
 webserver port 80 language en
 sntp-client
 # Put in your primary and secondary SNTP time server
 sntp-client server primary xxx.xxx.xxx.xxx port 123 version 4
 sntp-client server secondary xxx.xxx.xxx.xxx port 123 version 4
 sntp-client poll-interval 36000
 sntp-client local-clock-offset
 # Enter your gateway's fqdn
 system hostname gateway.xyz.com
 
 system
 
   ic voice 0
     pcm law-select uLaw
 
 system
   clock-source 1 e1t1 0 0
   clock-source 2 internal
 
 profile napt NAPT_WAN
 
 profile napt NAPT
 
 profile ppp default
 
 profile call-progress-tone US_Dialtone
 
 profile call-progress-tone US_Alertingtone
   play 1 2000 440 -19 480 -19
   pause 2 4000
 
 profile call-progress-tone US_Busytone
   play 1 500 480 -24 620 -24
   pause 2 500
 
 profile tone-set default
 
 profile tone-set US
   map call-progress-tone dial-tone US_Dialtone
   map call-progress-tone ringback-tone US_Alertingtone
   map call-progress-tone busy-tone US_Busytone
   map call-progress-tone release-tone US_Busytone
   map call-progress-tone congestion-tone US_Busytone
 
 profile voip default
   codec 1 g711ulaw64k rx-length 20 tx-length 20
   codec 2 g711alaw64k rx-length 20 tx-length 20
 
 profile pstn default
 
 profile sip default
 
 profile aaa default
   method 1 local
   method 2 none
 
 context ip router
 
   interface WAN
     ipaddress dhcp
     use profile napt NAPT_WAN
     tcp adjust-mss rx mtu
     tcp adjust-mss tx mtu
 
   interface LAN
     # Enter the IP address of your gateway
     ipaddress xxx.xxx.xxx.xxx 255.255.255.0
     tcp adjust-mss rx mtu
     tcp adjust-mss tx mtu
 
 context ip router
   # Enter your default gateway
   route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 0
 
 context cs switch
   digit-collection timeout 4
 
   routing-table called-e164 TAB_OUT
     route .%T dest-interface IF-SIP1
 
   routing-table called-e164 TAB_IN
     route default dest-service OUTBOUND
 
   mapping-table called-e164 to called-e164 STIP-ALL
     map default to ""
 
   interface isdn IF_PRI_1
     route call dest-table TAB_OUT
     use profile tone-set US
     caller-name send-information-following
     user-side-ringback-tone
 
   interface sip IF-SIP1
     bind gateway GW-SIP
     service default
     route call dest-table TAB_IN
     # Enter your SIP domain name
     remote xyz.com
     no address-translation incoming-call calling-uri
 
   service hunt-group OUTBOUND
     drop-cause normal-unspecified
     drop-cause no-circuit-channel-available
     drop-cause network-out-of-order
     drop-cause temporary-failure
     drop-cause switching-equipment-congestion
     drop-cause access-info-discarded
     drop-cause circuit-channel-not-available
     drop-cause resources-unavailable
     route call 1 dest-interface IF_PRI_1
 
 context cs switch
   no shutdown
 
 gateway sip GW-SIP
   bind interface LAN router
 
   service default
     # Enter your SIP domain name below
     registration manual xyz.com
 
 gateway sip GW-SIP
   no shutdown
 
 port ethernet 0 0
   medium auto
   encapsulation ip
   bind interface WAN router
   no shutdown
 
 port ethernet 0 1
   medium auto
   encapsulation ip
   bind interface LAN router
   no shutdown
 
 port e1t1 0 0
   port-type t1
   clock slave
   linecode b8zs
   framing esf
   encapsulation q921
 
  q921
     permanent-layer2
     uni-side user
     encapsulation q931
 
     q931
       # set your protocol to ni2 might also be dms100
       protocol ni2
       uni-side user
       bchan-number-order ascending-cyclic
       encapsulation cc-isdn
       bind interface IF_PRI_1 switch
 
 port e1t1 0 0
   no shutdown
 
 port e1t1 0 1
   port-type e1
   clock master
   framing crc4
   shutdown
 
 port e1t1 0 2
   port-type e1
   clock master
   framing crc4
   shutdown
 
 port e1t1 0 3
   port-type e1
   clock master
   framing crc4
   shutdown